We're extremely excited by how things are going with this project. Our Kickstarter campaign has successfully funded on June 2! We will send you newsletter when the Jadelabo J1 Pre-order is available.
Printing
Print Head System
Independent Dual Extruder System (IDEX)
Build Volume (W×D×H)
Single Extruder Mode / Support Mode / Multimaterial Mode: 320x210x200 mm (12.6x8.3x7.9 in)
Duplication Mode: 160x210x200 mm (6.3x8.3x7.9 in)
Mirror Mode: 150x210x200 mm (5.9x8.3x7.9 in)
Print Head Travel Speed
Up to 150 mm/s
Nozzle Diameter
Layer Height
Nozzle Temperature
0.4mm
0.05 - 0.3 mm
Up to 300 ℃
Self-Test Procedure, Power Loss Detection & Recovery, Filament Runout Detection & Recovery, Filament Tangles Detection & Recovery, Backup Mode, Avoid-Losing-Both Mode, Pause Recovery (the power could be turned off during the pause)
Heated Bed Temperature
Smart Features
Up to 110 ℃
Printer
Type
Fully Assembled
Aluminum Alloys
Frame Material
Connectivity
Wi-Fi, USB Cable, USB Flash Drive
Touchscreen
5" Full-Color Capacitive, 1280 x 720
ARM Cortex-A53
1GB RAM, 8GB EMMC
Controller Board
32 Bit Processor
ARM Cortex-M4
TMC2209
Materials
Filament Diameter
1.75mm
Supported Materials
PLA / PETG / ABS / ASA / TPU / PVA / PC / PA
Electrical
Input
100 - 240 V, 6A max., 50 / 60 Hz
Power Consumption
400W max.
Software & Firmware
Slicer
Jadelabo Cura. Or third-party slicers.
Windows, Mac, Linux
Operating System
Supported Files
STL, OBJ, 3MF, AMF
Marlin
Firmware
Open Source
Software, Firmware
Notice: The specifications listed might be slightly changed in any meaningful way when we refine these products.
Independent Dual Extruder (IDEX)
CPU
ARM Cortex-M4
ARM Cortex-A53
Memory
1GB RAM
8GB EMMC
Rated Power
400W
Motor Driver
TMC2209
Noiseless Operation
Stall Detection
Multi-material Mode
You never know what you can make until you try. Combine materials to obtain different mechanical properties or colors in one single print. Make something new, explorative, and fabulous.
Mirror Mode
Work independently. Work efficiently. The IDEX mirror mode enables the dual extruders to work symmetrically and simultaneously. When printing mirrored objects or symmetrical objects in J1, you can save half the printing time.
Duplication Mode
Double the production capacity. When printing identical objects, you can print twice as many parts as you would get with a regular single-extruder 3D printer. So it doubles the printing efficiency without adding the cost of buying another 3D printer.
Backup Mode and More
Two is better than one. When printing in single mode, you can set J1 into backup mode. If the print head at work gets clogged or its filament runs out, J1 would stop it and start the other print head to resume the print automatically. More modes are being tested internally and will be introduced when they are ready.
Materials
Print Heads
A Wide Range of Materials
Print a variety of materials with ease. From the print heads, heated bed, motion mechanism, and enclosure addon, all the components and structures in J1 are carefully designed to work efficiently with various materials.
Support:
PLA / PETG / ABS / ASA / TPU / PVA / PC / PA
In Testing:
PA-CF / PA-GF
Performance
Direct Drive & Dual Drive
J1 has great compatibility with a broader range of materials and a fine control of retraction. The direct drive setup offers a highly responsive extrusion system. As the dual drive setup grips and controls the filament from both sides, the setup can deliver a consistent flow of filament. Combining these two setups, J1 can print flexible material with better results.
Compact & Integrated System
J1's print heads are packed with various powerful features to deliver a reliable and easy-to-use printing experience. Covered with strong and transparent housings, the print heads allow you to see through the head to know filament status.
Precise Nozzle Height Calibration
It will result in a failed print if your dual extruder is not aligned correctly. However, for most IDEX 3D printers, dual extruder calibration is quite complicated and difficult. For J1, we've designed a special structure for precise nozzle calibration. You can adjust the nozzle height much more precisely by following the instructions on the touchscreen to turn the knob to a specific value.
Jams & Filament Runout Sensor
Each print head in J1 includes a filament sensor to detect, autopause, and alert you about not only filament runout but also filament jams. The sensor can help prevent ruining your prints or the hotend, save the material and power. In the case of filament running out, J1 can even let you resume the print after the problem is fixed.
Various Sizes & Easy-to-Detach Hotends
J1 is not only compatible with nozzles in various diameters, but also enabling you to use two different nozzles in one single print, which is a super cool feature using the IDEX system. You can use the 0.4 mm nozzle for daily prints, use the 0.2 mm nozzle to obtain the finest details, and use the 0.6 mm and 0.8 mm nozzles to speed up the print or print stronger parts.
Specs
Sign Up for Pre-order News
Support Mode
You can use a secondary material as supports to print complex geometries and get smoother surface with crisp details. The support material can be dissolvable materials like PVA. You can also save on premium materials by printing the main body with them, and printing supports with a regular and cheaper material.
Build Plate
Glass Plate with PEI Print Surface
Featuring a glass plate with the Polyetherimide (PEI) print surface, J1 offers an ideal build plate for 3D printing with a wide variety of materials. The glass plate is reliably flat, thermally stable, and extremely durable. The PEI print surface offers excellent adhesion and easier print removal for a printed object.
The Latest News
Touchscreen
Intuitive and Powerful
J1 features a 5" full-color capacitive IPS touchscreen. It provides an initial setup wizard, clear illustrations, instant notifications, real-time machine and print status to give you a better printing experience. Running Tina Linux, it offers various features that let you easily control J1 with a few touches.
Calibration
More Precise and Quicker
Calibrating an IDEX 3D printer used to be a tedious process, requiring a lot of manual work and experience. For both bed and dual extruder calibrations, J1 provides a quicker and semi-auto way to achieve precise calibration.
For more details, join our mailing list to learn more.
Jadelabo J1
Independent Dual Extruder 3D Printer
Beautiful. Powerful. Smart.
Subscribe to our newsletter for PRE-ORDER NEWS!
