bobnoir Posté(e) Avril 8, 2020 Posté(e) Avril 8, 2020 Bonjour! VAP38 , j'ai du changer l'ensemble buse et corps de chauffe de mon A10M ( impossible d'enlever la buse ) et j'aimerai bien installer votre marlin 2.0. Es ce qui'l est stable? Je demande parce que dans le file de discussion, a la suite, il semble y avoir des soucis . merci d'avance.
vap38 Posté(e) Avril 8, 2020 Posté(e) Avril 8, 2020 Bonjour, Pour démonter la buse il faut chauffer l'extrudeur à 190° et prendre une clé de 7MM il faut abloquer le corps de chauffe avec une clé à molette ajustée à la largeur du corps de chauffe . Attention aux fils de chauffe et de la sonde çà doit fonctionner. (mettre des gants pour se protéger les mains) Pour Marlin j'attends de faire des essais avec le nouvelle version 2.05 ! En ce moment je suis sur une nouvelle machine TENLOG TLD3PRO en cours de tests et impressions en cours. a+
pouxirate Posté(e) Avril 8, 2020 Auteur Posté(e) Avril 8, 2020 salut, sur la fin après toutes les modifications j'arrivais à imprimer des pièces avec pas mal de précision, l’esthétique était bien aussi. Après stable je peux pas me prononcer, je pense qu'il y a toujours des modifications possibles. il y a juste le moteur de l'extrudeur qui tourne beaucoup plus qu'avant et donc qui chauffe plus. après en le refroidissant un peu ça devrait le faire, c'était le dernier point sur lequel je travaillais avant que je crame ma carte mère ( rien a voir avec marlin, erreur de gros doigt). voila! Moi je vais continuer avec une skr 1.3 et toujours marlin 2 car le mode de fonctionnement est mieux. Bon courage à toi. Et si tu as besoin tu peux toujours demander de l'aide, on aura peut être la réponse.
bobnoir Posté(e) Avril 8, 2020 Posté(e) Avril 8, 2020 Cool je vais tester avec les fichiers postés le 1 février . Pour la buse j'ai essayé d'abord à chaud puis à froid rien y à fait...de toute façon les changement sont fait mais mes ventilos d2connent j'en ai commandé de nouveaux avant de cramer l'ensemble ... Un grand merci messieurs, j'ai hâte de tester ça !
bobnoir Posté(e) Avril 8, 2020 Posté(e) Avril 8, 2020 Ah, j'avais oublié, tu as mis à jour la carte mère ( CH340)? si oui je veux bien le nom du logiciel, j'avais HexUploader mais je ne retrouve pas.
bobnoir Posté(e) Avril 8, 2020 Posté(e) Avril 8, 2020 La skr 1.3 à l'air bien en effet mais niveau bricolage ça passe au niveau supérieur on dirait.
fran6p Posté(e) Avril 9, 2020 Posté(e) Avril 9, 2020 Le 08/04/2020 at 23:48, bobnoir a dit : j'avais HexUploader mais je ne retrouve pas. Dérouler C'est plutôt Xloader (interface à avrdude).
pouxirate Posté(e) Avril 9, 2020 Auteur Posté(e) Avril 9, 2020 (modifié) Le 08/04/2020 at 23:48, bobnoir a dit : j'avais oublié, tu as mis à jour la carte mère ( CH340) Dérouler non je n'ai rien mis a jour, j'ai acheté l'imprimante d'occasion. et pour la skr1.3 on verra bien, çà doit pas être insurmontable! Et puis je pense que je trouverais de l'aide sur ce forum. Modifié (le) Avril 9, 2020 par pouxirate
casimir.24 Posté(e) Avril 17, 2020 Posté(e) Avril 17, 2020 (modifié) bonjour voici le fichier de l'erreur cordialement Arduino.pdfFetching info... Modifié (le) Avril 17, 2020 par casimir.24
fran6p Posté(e) Avril 17, 2020 Posté(e) Avril 17, 2020 @casimir.24 Bonjour, Sais-tu qu'il est possible de joindre des fichiers dans un post ? Là en polluant la lecture par ton fichier journal des erreurs, honnêtement je en vois pas bien ce qu'on peut en faire (et en plus ça donne pas envie ). L'intérêt de mettre le journal en pièce jointe est qu'alors on peut (ou pas) utiliser n'importe quel éditeur de texte pour y effectuer des recherches par exemple.
casimir.24 Posté(e) Avril 17, 2020 Posté(e) Avril 17, 2020 bonjour désoler oui je supprime le post et poste le fichier
Nadine Lhce Posté(e) Avril 19, 2020 Posté(e) Avril 19, 2020 bonsoir chez moi ca ne marche pas j ai #if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
pouxirate Posté(e) Avril 19, 2020 Auteur Posté(e) Avril 19, 2020 bonjour Nadine Lhce , Ce qui serait bien bien avant tout, c'est de mettre beaucoup plus de détails. quelle imprimante, carte mère utilises tu? quelle version de marlin utilises tu? avec quoi as tu téléversé marlin et la version? possèdes tu un bltouch? as tu fait des changements dans configuration.h et Configuration_adv.h? pareil pour casimir.24.
pouxirate Posté(e) Avril 19, 2020 Auteur Posté(e) Avril 19, 2020 (modifié) Nadine Lhce dans Configuration_adv.h as tu décommenté //#define LASER_FEATURE? Tu utilises marlin sur une imprimante pour faire de l'impression 3d? Modifié (le) Avril 19, 2020 par pouxirate
Nadine Lhce Posté(e) Avril 19, 2020 Posté(e) Avril 19, 2020 j ai marlin1.1.8 sur geeetehc A10 carte GT256 V3 sans BLT
pouxirate Posté(e) Avril 19, 2020 Auteur Posté(e) Avril 19, 2020 donc du coup les fichiers de configurations que j'ai laissé sont pour marlin 2.0.4.4. Il te faut télécharger marlin 2.0.4.4 et changer les fichiers configuation.h et Configuration_adv.h par ceux que j'ai donné plus haut (copier/coller). Par contre il y aura quelques changements à faire, car moi j'ai un 3dtouch et j'ai changé mon extrudeur. Ensuite tu téléverses et tu testes.
Nadine Lhce Posté(e) Avril 19, 2020 Posté(e) Avril 19, 2020 Quelle con ba oui j ai pas telecharger la bon marlin quelle version me conseille tu 2.0.5.3 oula bugfix 2.0.x ?
pouxirate Posté(e) Avril 19, 2020 Auteur Posté(e) Avril 19, 2020 (modifié) moi j'ai fait des tests avec 2.0.4.4 mais avec 2.0.5.3 cela devrait fonctionné aussi. par contre pense a modifier les fichiers de configurations car on est pas sur la même configuration d'imprimante. Modifié (le) Avril 19, 2020 par pouxirate
Nadine Lhce Posté(e) Avril 19, 2020 Posté(e) Avril 19, 2020 merde la tu ma perdu qu appelle tu configuration d'imprimante.
pouxirate Posté(e) Avril 19, 2020 Auteur Posté(e) Avril 19, 2020 (modifié) ma geeetech a10 comme la tienne possède une GT2560 v3.0 mais moi j'ai un 3dtouch et un extrudeur type BMG en plus. Donc déja pour le 3dtouch : tu inverses les lignes à commenter et décommenter II) Activation du 3dtouch a) commenter les lignes suivantes : 847 //#define PROBE_MANUALLY 848 //#define MANUAL_PROBE_START_Z 0.2 b) décommenter les lignes suivantes : 871 #define BLTOUCH 1343 #define Z_SAFE_HOMING Modifié (le) Avril 19, 2020 par pouxirate
Nadine Lhce Posté(e) Avril 19, 2020 Posté(e) Avril 19, 2020 ok merci et c est tout ce que j ai a faire?
pouxirate Posté(e) Avril 19, 2020 Auteur Posté(e) Avril 19, 2020 (modifié) Le 19/04/2020 at 12:54, Nadine Lhce a dit : ok merci et c est tout ce que j ai a faire? Dérouler te voici les fichiers de configurations pour marlin 2.0.5 ils sont vierges juste l'essentiel pas de bltouch et extrudeur d'origine. Par contre je sais pas si tu as l'habitude de flasher des firmwares mais faut bidouiller un peu voir pas mal et si tu ni arrives pas il te faudra refaire marche arrière avec un malrin d'origine. Configuration.hFetching info... Configuration_adv.hFetching info... Modifié (le) Avril 19, 2020 par pouxirate
Nadine Lhce Posté(e) Avril 19, 2020 Posté(e) Avril 19, 2020 Citation Dérouler oui je l ai deja fait mais il y a longtemps
pouxirate Posté(e) Avril 19, 2020 Auteur Posté(e) Avril 19, 2020 ok ça roule, j'espère que cela va fonctionner pour toi!
Nadine Lhce Posté(e) Avril 19, 2020 Posté(e) Avril 19, 2020 bon ca marche pas Arduino : 1.8.7 (Windows 10), Carte : "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)" In file included from sketch\src\gcode\motion\../../inc/MarlinConfig.h:40:0, from sketch\src\gcode\motion\G2_G3.cpp:23: sketch\src\gcode\motion\../../inc/SanityCheck.h:76:4: error: #error "You are using an old Configuration.h file, update it before building Marlin." #error "You are using an old Configuration.h file, update it before building Marlin." ^ In file included from sketch\src\gcode\motion\../../inc/MarlinConfig.h:40:0, from sketch\src\gcode\motion\G2_G3.cpp:23: sketch\src\gcode\motion\../../inc/SanityCheck.h:80:4: error: #error "You are using an old Configuration_adv.h file, update it before building Marlin." #error "You are using an old Configuration_adv.h file, update it before building Marlin." ^ sketch\src\gcode\motion\../../inc/SanityCheck.h:104:4: error: #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." ^ sketch\src\gcode\motion\../../inc/SanityCheck.h:765:6: error: #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." ^ In file included from sketch\src\HAL\AVR\../../inc/MarlinConfig.h:40:0, from sketch\src\HAL\AVR\HAL.cpp:25: sketch\src\HAL\AVR\../../inc/SanityCheck.h:76:4: error: #error "You are using an old Configuration.h file, update it before building Marlin." #error "You are using an old Configuration.h file, update it before building Marlin." ^ In file included from sketch\src\HAL\AVR\../../inc/MarlinConfig.h:40:0, from sketch\src\HAL\AVR\HAL.cpp:25: sketch\src\HAL\AVR\../../inc/SanityCheck.h:80:4: error: #error "You are using an old Configuration_adv.h file, update it before building Marlin." #error "You are using an old Configuration_adv.h file, update it before building Marlin." ^ sketch\src\HAL\AVR\../../inc/SanityCheck.h:104:4: error: #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." ^ sketch\src\HAL\AVR\../../inc/SanityCheck.h:765:6: error: #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." ^ In file included from sketch\src\gcode\motion\../../inc/MarlinConfig.h:40:0, from sketch\src\gcode\motion\G5.cpp:23: sketch\src\gcode\motion\../../inc/SanityCheck.h:76:4: error: #error "You are using an old Configuration.h file, update it before building Marlin." #error "You are using an old Configuration.h file, update it before building Marlin." ^ In file included from sketch\src\gcode\motion\../../inc/MarlinConfig.h:40:0, from sketch\src\gcode\motion\G5.cpp:23: sketch\src\gcode\motion\../../inc/SanityCheck.h:80:4: error: #error "You are using an old Configuration_adv.h file, update it before building Marlin." #error "You are using an old Configuration_adv.h file, update it before building Marlin." ^ sketch\src\gcode\motion\../../inc/SanityCheck.h:104:4: error: #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." ^ sketch\src\gcode\motion\../../inc/SanityCheck.h:765:6: error: #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." ^ exit status 1 In file included from sketch\src\gcode\motion\../../inc/MarlinConfig.h:40:0, from sketch\src\gcode\motion\../gcode.h:286, from sketch\src\gcode\motion\G4.cpp:23: sketch\src\gcode\motion\../../inc/SanityCheck.h:76:4: error: #error "You are using an old Configuration.h file, update it before building Marlin." #error "You are using an old Configuration.h file, update it before building Marlin." ^ In file included from sketch\src\gcode\motion\../../inc/MarlinConfig.h:40:0, from sketch\src\gcode\motion\../gcode.h:286, from sketch\src\gcode\motion\G4.cpp:23: sketch\src\gcode\motion\../../inc/SanityCheck.h:80:4: error: #error "You are using an old Configuration_adv.h file, update it before building Marlin." #error "You are using an old Configuration_adv.h file, update it before building Marlin." ^ sketch\src\gcode\motion\../../inc/SanityCheck.h:104:4: error: #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." ^ sketch\src\gcode\motion\../../inc/SanityCheck.h:765:6: error: #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." ^ In file included from sketch\src\inc/MarlinConfig.h:40:0, from sketch\src\MarlinCore.h:24, from sketch\src\MarlinCore.cpp:31: sketch\src\inc/SanityCheck.h:76:4: error: #error "You are using an old Configuration.h file, update it before building Marlin." #error "You are using an old Configuration.h file, update it before building Marlin." ^ In file included from sketch\src\inc/MarlinConfig.h:40:0, from sketch\src\MarlinCore.h:24, from sketch\src\MarlinCore.cpp:31: sketch\src\inc/SanityCheck.h:80:4: error: #error "You are using an old Configuration_adv.h file, update it before building Marlin." #error "You are using an old Configuration_adv.h file, update it before building Marlin." ^ sketch\src\inc/SanityCheck.h:104:4: error: #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." ^ sketch\src\inc/SanityCheck.h:765:6: error: #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." ^ In file included from sketch\src\HAL\AVR\../../inc/MarlinConfig.h:40:0, from sketch\src\HAL\AVR\MarlinSerial.cpp:39: sketch\src\HAL\AVR\../../inc/SanityCheck.h:76:4: error: #error "You are using an old Configuration.h file, update it before building Marlin." #error "You are using an old Configuration.h file, update it before building Marlin." ^ In file included from sketch\src\HAL\AVR\../../inc/MarlinConfig.h:40:0, from sketch\src\HAL\AVR\MarlinSerial.cpp:39: sketch\src\HAL\AVR\../../inc/SanityCheck.h:80:4: error: #error "You are using an old Configuration_adv.h file, update it before building Marlin." #error "You are using an old Configuration_adv.h file, update it before building Marlin." ^ sketch\src\HAL\AVR\../../inc/SanityCheck.h:104:4: error: #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." ^ sketch\src\HAL\AVR\../../inc/SanityCheck.h:765:6: error: #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." ^ In file included from sketch\src\HAL\AVR\../../inc/MarlinConfig.h:40:0, from sketch\src\HAL\AVR\eeprom.cpp:24: sketch\src\HAL\AVR\../../inc/SanityCheck.h:76:4: error: #error "You are using an old Configuration.h file, update it before building Marlin." #error "You are using an old Configuration.h file, update it before building Marlin." ^ In file included from sketch\src\HAL\AVR\../../inc/MarlinConfig.h:40:0, from sketch\src\HAL\AVR\eeprom.cpp:24: sketch\src\HAL\AVR\../../inc/SanityCheck.h:80:4: error: #error "You are using an old Configuration_adv.h file, update it before building Marlin." #error "You are using an old Configuration_adv.h file, update it before building Marlin." ^ sketch\src\HAL\AVR\../../inc/SanityCheck.h:104:4: error: #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." ^ sketch\src\HAL\AVR\../../inc/SanityCheck.h:765:6: error: #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." ^ In file included from sketch\src\HAL\AVR\../../inc/MarlinConfig.h:40:0, from sketch\src\HAL\AVR\watchdog.cpp:25: sketch\src\HAL\AVR\../../inc/SanityCheck.h:76:4: error: #error "You are using an old Configuration.h file, update it before building Marlin." #error "You are using an old Configuration.h file, update it before building Marlin." ^ In file included from sketch\src\HAL\AVR\../../inc/MarlinConfig.h:40:0, from sketch\src\HAL\AVR\watchdog.cpp:25: sketch\src\HAL\AVR\../../inc/SanityCheck.h:80:4: error: #error "You are using an old Configuration_adv.h file, update it before building Marlin." #error "You are using an old Configuration_adv.h file, update it before building Marlin." ^ sketch\src\HAL\AVR\../../inc/SanityCheck.h:104:4: error: #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." ^ sketch\src\HAL\AVR\../../inc/SanityCheck.h:765:6: error: #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." ^ In file included from sketch\src\gcode\probe\../../inc/MarlinConfig.h:40:0, from sketch\src\gcode\probe\G30.cpp:23: sketch\src\gcode\probe\../../inc/SanityCheck.h:76:4: error: #error "You are using an old Configuration.h file, update it before building Marlin." #error "You are using an old Configuration.h file, update it before building Marlin." ^ In file included from sketch\src\gcode\probe\../../inc/MarlinConfig.h:40:0, from sketch\src\gcode\probe\G30.cpp:23: sketch\src\gcode\probe\../../inc/SanityCheck.h:80:4: error: #error "You are using an old Configuration_adv.h file, update it before building Marlin." #error "You are using an old Configuration_adv.h file, update it before building Marlin." ^ sketch\src\gcode\probe\../../inc/SanityCheck.h:104:4: error: #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." ^ sketch\src\gcode\probe\../../inc/SanityCheck.h:765:6: error: #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." ^ In file included from sketch\src\gcode\probe\../../inc/MarlinConfig.h:40:0, from sketch\src\gcode\probe\G38.cpp:23: sketch\src\gcode\probe\../../inc/SanityCheck.h:76:4: error: #error "You are using an old Configuration.h file, update it before building Marlin." #error "You are using an old Configuration.h file, update it before building Marlin." ^ In file included from sketch\src\gcode\probe\../../inc/MarlinConfig.h:40:0, from sketch\src\gcode\probe\G38.cpp:23: sketch\src\gcode\probe\../../inc/SanityCheck.h:80:4: error: #error "You are using an old Configuration_adv.h file, update it before building Marlin." #error "You are using an old Configuration_adv.h file, update it before building Marlin." ^ sketch\src\gcode\probe\../../inc/SanityCheck.h:104:4: error: #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration." ^ sketch\src\gcode\probe\../../inc/SanityCheck.h:765:6: error: #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." #error "ADVANCED_PAUSE_FEATURE requires FILAMENT_UNLOAD_PURGE_FEEDRATE. Please add it to Configuration_adv.h." ^ Erreur de compilation pour la carte Arduino/Genuino Mega or Mega 2560 Ce rapport pourrait être plus détaillé avec l'option "Afficher les résultats détaillés de la compilation" activée dans Fichier -> Préférences.
Messages recommandés