Aller au contenu

GO Print

double extrusion smoothie MKS SBASE


cmatec

Messages recommandés

Pour le réglage du servo de la bascule il va falloir utiliser repetier (ou équivalent). Connecter la mks sbase et passer en mode manuel. L'objectif est de mettre la bascule en butée pour la tête 1 et 2. Pour cela nous allons utiliser la commande M280 Sx  (x est la valeur à ajuster à vos butées). Au départ, il vaut mieux éviter les déplacements jusqu'en butée (jour entre l'aimant et la vis de butée) et ajuster au fur et à mesure pour trouver les valeurs correctes (notez les sur une feuille ou autre ...).

600375793_offsetrepetier.png.c940b30524aaa7f39fc56cdbdc7188e0.png

Toujours sous repetier, nous allons passer au réglage des offsets X et Y (je ne parlerai pas du calage en Z des 2 buses ici). La méthode la plus rapide (et assez fiable) que j'ai trouvé est d'utiliser de la colle en stick sur le plateau verre. Tartinez une surface de 5x5cm et positionnez votre bascule au dessus. Mettez en butée la tête 1 et faire descendre la buse au contact du plateau. On déplace le plateau selon l'axe Y ... 1 trait dans la colle. On relève un peu le Z, passage de la tête 2 en butée et on procède de même. Pour avoir l'écartement des 2 buses, il suffit de mesurer au pied à coulisse l'écartement des 2 traits.

Normalement, il ne doit pas y avoir d'offset en Y. Pour le vérifier, la méthode est la même sauf qu'au lieu de déplacer le plateau, on déplace le chariot en X.

Une fois les mesures effectuées, il faut les renseigner dans le config.txt :

extruder.hotend.x_offset                        9           # X offset from origin in mm
extruder.hotend.y_offset                        0            # Y offset from origin in mm
extruder.hotend.z_offset                        0            # Z offset from origin in mm

extruder.hotend2.x_offset                       -9          # X offset from origin in mm
extruder.hotend2.y_offset                       0            # Y offset from origin in mm
extruder.hotend2.z_offset                       0            # Z offset from origin in mm

Sur ma bascule, l'écartement des 2 buses à la mesure est de 18mm. J'ai choisi de répartir l'offset sur les 2 têtes pour éviter de trop perdre en surface de print.

Si vous utilisez un auto level style bl touch ou touch mi, il faudra renseigner les offset par rapport au centre des 2 buses :

leveling-strategy.rectangular-grid.probe_offsets        0,0,0      # Optional probe offsets from the nozzle or tool head

Modifié (le) par cmatec
Lien vers le commentaire
Partager sur d’autres sites

Il y a aussi la possibilité de faire (en automatique) une série de traits (ex: 10 traits tous les 1 mm avec la tête 1) et la même chose juste en vis à vis, 10 traits tous les 0.9mm avec la tête 2.

On regarde ensuite quels traits sont parfaitement alignés (comme la lecture d'un vernier) et on trouve ainsi de combien il faut décaler une tête par rapport à l'autre.

Lien vers le commentaire
Partager sur d’autres sites

Il y a 4 heures, cmatec a dit :

ce genre de test de calibration : https://www.thingiverse.com/thing:1526735

C'est du lourd !

Mais dis donc ... pas besoin de passer 2 Kg de filament pour voir si les têtes sont bien alignées !  😉

On peut faire plus simple et surtout plus rapide, mais sinon c'est exactement le principe du vernier dont je parlais.

Lien vers le commentaire
Partager sur d’autres sites

Le 20/10/2018 at 13:34, cmatec a dit :

Hello tous !

Lors des premiers messages, je présentais les différents types de hotend dédiées pour le dual, chacun ayant ses avantages et inconvénients. Il est donc devenu évident qu'une évolution était nécessaire : une double tête montée sur un système de bascule. En images ...

1685426004_presentationbascule.png.ee0b4c7437d2efec0a40aa6b6ccc3bf8.png

... et les fichiers : bascule.zip

Je détaillerai la "liste de courses" nécessaire à son fonctionnement ainsi que la stratégie mise en place pour le pilotage de la bascule sous smoothie.

Il y a encore du travail à accomplir mais je pense que c'est une bonne base à adapter sur nos imprimantes "grand public".

D'autres solutions sont à l'étude : https://www.lesimprimantes3d.fr/forum/topic/17502-double-extrusion-à-bascule-coté-mécanique/

La tête rotative, me semble plus que prometteuse !

A suivre.

Salut @cmatec, tu pourrais mettre des schémas selon d'autres angles de vue pour le montage des 4 pièces du support ? Et où sont fixées les 2 têtes et le ventilo ?

Des photos de ta tête d'impression sans le ventilo et selon différents angles, ça serait top.

Là, j'arrive à ça sous TinkerCAD mais je pense pas que ça soit bon (si c'est la pièce rose qui est doit basculer) :

image.png.8f3d246a5ca5a0a7db80576ce1db25ee.png

Lien vers le commentaire
Partager sur d’autres sites

il y a 49 minutes, mikebzh44 a dit :

e pense pas que ça soit bon (si c'est la pièce rose qui est doit basculer) :

La pièce rose bascule ainsi que la pièce grise, par contre la pièce rose est trop haute

Lien vers le commentaire
Partager sur d’autres sites

... J'ai choisi cura 3.5 car il permet d'éditer un module "g-code avant/après changement d'extrudeur" pour chaque tête. On peut ainsi y intégrer très clairement le pilotage de la bascule

1186773719_configurationmachine.png.b41fd0f2b53af29ebdb921492f463f56.png

La photo intègre aussi la partie start/end g-code et cela va avoir son importance pour la suite.

Le problème rencontré sous smoothie est la gestion des outils car ils partagent la même commande g-code pour leur activation (cf config.txt):

temperature_control.hotend.set_m_code                       104
temperature_control.hotend.set_and_wait_m_code  109

temperature_control.hotend2.set_m_code                      104
temperature_control.hotend2.set_and_wait_m_code 109

Pour contourner le problème du changement d'outil (et avoir un g-code utilisable par smoothie), je défini le "tool"initial (T0) et place la bascule en conséquence (M280 S7). Ensuite, il va falloir être très attentif à la gestion des températures dans cura ... car tout changement de température (appelé avec un M104 ou M109) implique un changement d'outil sous smoothie ... et avec la bascule, ça devient vite le bazar !!!

Pour être sûr de ne passer à côté de rien, il faut activer la visibilité de tous les paramètres (settings/configure setting visibility).

2013893955_curagestiontemperatures.png.a6171acdd137877f11fea42847d8c31a.png

Il faut fixer une valeur de température adaptée au filament et seulement une ... sinon ça risque de partir rapidement en sucette.

Les modules extrudeurs étant indépendants, il est possible de définir des températures différentes pour chaque tête, mais à la condition de respecter le principe cité précédemment.

Le g-code généré par cura est correctement interprété par smoothie. Il n'y aura qu'une ligne de g-code à supprimer mais j'y reviendrai plus tard.

140179965_exemplegcodepropre.png.5bdc86fdd80ac99186b5982673f0856c.png

On voit bien que les outils sont clairement appelés ; ainsi que le pilotage du servo.

Si l'on ne procède pas de cette manière :

277730738_erreurgcode.png.5e2a51150e59bbe29ec8de948a53669a.png

On a un M109 Sx après le tool qui est activé (ici T1). Smoothie interprète cela comme un changement d'outil ... fin du print.

Pour le moment, c'est le moyen que j'ai trouvé pour contourner le problème de la gestion d'outil sous smoothie. Il n'est certes pas le plus abouti mais il a le mérite d'être fonctionnel avec la bascule. A ce stade, une fois le g-code généré par cura, il n'y a qu'une seule ligne à supprimer pour le rendre parfaitement opérationnel. Pour cela, il faut ouvrir le fichier g-code avec un éditeur (j'utilise repetier) et lancer une recherche  : M104 Tx S0 (tester T0 et T1). La recherche doit nous renvoyer vers la fin du g-code. Il faut supprimer la ligne pour éviter le changement d'outil appelé par le M104.

1994400740_editiongcode.png.2847fb69ad30c222877f1bb799365a86.png

Voilà, j'ai fais avec mes moyens pour arriver à faire fonctionner le système de bascule sous smoothie. Et c'est sacrément efficace pour parer aux suintements intempestifs de la tête inactive.

924811620_printsbascule.png.fa15730542fedc9acdc341be38b8e0d3.png

Modifié (le) par cmatec
  • J'aime 1
Lien vers le commentaire
Partager sur d’autres sites

Le ‎22‎/‎10‎/‎2018 at 18:58, cmatec a dit :

On a un M109 Sx après le tool qui est activé (ici T1). Smoothie interprète cela comme un changement d'outil ... fin du print.

Cette semaine j'ai un peu de temps, je vais regarder le gcode que sort S3D et savoir si c'est la même chose

Lien vers le commentaire
Partager sur d’autres sites

  • 3 weeks later...

@cmatec tu m'avais mis sur la piste, je pense avoir trouvé la solution

pour le changement d'outil, il faut ces 2 lignes de code pour chaque extrudeur

{IF NEWTOOL=0}M280 S6.68 ;
{IF NEWTOOL=1}M280 S7.6 ;

Lien vers le commentaire
Partager sur d’autres sites

il y a 10 minutes, cmatec a dit :

si c'est pris en compte par repetier, you're the boss !!!

c'est pris en compte par S3D mais j'ai pas testé sur repetier et j'ai pas envi de me prendre la tête, déjà que S3D a failli passer par la case désinstallation 😉 

Lien vers le commentaire
Partager sur d’autres sites

@pascal_lb : commande if_newtool=X non fonctionnellle sous repetier. {IF_EXTRUDER_X} M280 Sn fonctionne. Mais la commande IF ne semble pas prise en compte ... exemple :

T0                                             avant changement d'extrudeur
G92 E0
T1
G92 E0
T1                                            appel de T1 par repetier (cura)
M280 S7                               après changement d'extrudeur
M280 S8
G0 E3
G92 E0

@Tircown : si tu pouvais nous aider sur ce coup là, ce serait top !!!

Ci-joint la liste des variables utilisables sous cura : http://files.fieldofview.com/cura/Replacement_Patterns.html

Lien vers le commentaire
Partager sur d’autres sites

@cmatec, j'ai un peu zieuté le code de smoothie et il n'est pas censé redéfinir l'outil sur M109/M104 s'il n'y a pas de T[x]. Comme tu l'as précisé, si un appel du genre M104 T0 S200 est fait, l'outil actif sera T0 par la suite. C'est vrai pour toute commande contenant T[X]. Le soucis c'est que Marlin ne fait pas la même connerie. Donc dans Cura - Machine Settings choisi un autre G-Code flavor que Marlin.

Inutile de mettre T0/T1 dans les extruders start G-code: il est d'office appelé. Il est donc en double dans le GCODE.

Je soupçonne M105 (get temperature) d'arrêter le print et non pas M109. M105 est une commande destinée aux softs comme RepetierHost et ce qui est sûr c'est que ça n'a rien à faire dans un fichier GCODE. Après avoir fait le changement de G-Code flavor et si ça persiste teste voir un fichier généré sans température de consigne et que tu auras nettoyé de ses M105.

Modifié (le) par Tircown
Lien vers le commentaire
Partager sur d’autres sites

Il y a 2 heures, Tircown a dit :

Inutile de mettre T0/T1 dans les extruders start G-code

je ne les ai pas mis non plus dans le changement d'outil

Modifié (le) par pascal_lb
Lien vers le commentaire
Partager sur d’autres sites

Le ‎20‎/‎10‎/‎2018 at 20:34, cmatec a dit :

La liste de courses :

4 inserts filetage M3 (fixation des 2 hotends)

@cmatec 

salut ton projet me plait bien, peux tu m'en dire plus sur le type d'insert a utiliser

prévois tu (dans un futur plus ou moins proche !) un système de soufflage / refroidissement au niveau des buses ?

Lien vers le commentaire
Partager sur d’autres sites

@supernono : pour les inserts, ce sont ceux là :

1212961171_insertsm3.jpeg.79c1fcf06bedb46d1e608412fc057ccc.jpeg

La ventilation auxiliaire est à l'étude pour le moment. J'ai testé une turbine en vis à vis du ventilateur de hotends mais cela perturbe leur refroidissement. Système déporté ? Captage du flux d'air du ventilateur de hotend (style neva) ? Il y a encore un peu de travail 😉

Lien vers le commentaire
Partager sur d’autres sites

  • 2 months later...

Hello tous !

Quelques retours sur l'utilisation de la bascule : L'alimentation via les connecteurs endstop et aux-1 ne semble pas suffisante et provoque le reboot de la mks sbase.

Une alimentation externe est donc à privilégier.

143560682_alimexterneservo.png.2be429bad527d72ded5d7050098642ff.png

Lien vers le commentaire
Partager sur d’autres sites

  • 1 year later...

Bonjour à tous,

J'essaye actuellement d'installer un double extrudeur chimera sur une imprimante que j'ai réalisé moi même.

Je bloque depuis quelques jours sur la configuration smoothiebord, je pense avoir réalisé les modification nécessaire dans la configuration ( true sur la ligne du deuxième extrudeur) mais impossible de pouvoir commander le deuxième extrudeur, en manuel toute les commande que je lance sont exécutées par l'extrudeur 1.

 

J'ai joint une copie de ma configuration ci-quelqu'un à une idée de ou peux provenir mon erreur j'en serais très reconnaissant.

 

Merci d'avance 😉 

 

# Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
# NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
## Robot module configurations : general handling of movement G-codes and slicing into moves

# Basic motion configuration
default_feed_rate                            4000             # Default speed (mm/minute) for G1/G2/G3 moves
default_seek_rate                            4000             # Default speed (mm/minute) for G0 moves
mm_per_arc_segment                           0.0              # Fixed length for line segments that divide arcs, 0 to disable
#mm_per_line_segment                         5                # Cut lines into segments this size
mm_max_arc_error                             0.01             # The maximum error for line segments that divide arcs 0 to disable
                                                              # note it is invalid for both the above be 0
                                                              # if both are used, will use largest segment length based on radius

# Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
# See http://smoothieware.org/stepper-motors
alpha_steps_per_mm                           80               # Steps per mm for alpha ( X ) stepper
beta_steps_per_mm                            80               # Steps per mm for beta ( Y ) stepper
gamma_steps_per_mm                           1600             # Steps per mm for gamma ( Z ) stepper

# Planner module configuration : Look-ahead and acceleration configuration
# See http://smoothieware.org/motion-control
acceleration                                 3000             # Acceleration in mm/second/second.
#z_acceleration                              500              # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
junction_deviation                           0.05             # See http://smoothieware.org/motion-control#junction-deviation
#z_junction_deviation                        0.0              # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA

# Cartesian axis speed limits
x_axis_max_speed                             30000            # Maximum speed in mm/min
y_axis_max_speed                             30000            # Maximum speed in mm/min
z_axis_max_speed                             300              # Maximum speed in mm/min

# Stepper module configuration
# Pins are defined as  ports, and pin numbers, appending "!" to the number will invert a pin
# See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
alpha_step_pin                               2.0              # Pin for alpha stepper step signal
alpha_dir_pin                                0.5              # Pin for alpha stepper direction, add '!' to reverse direction
alpha_en_pin                                 0.4              # Pin for alpha enable pin
alpha_current                                1.5              # X stepper motor current
alpha_max_rate                               30000.0          # Maximum rate in mm/min

beta_step_pin                                2.1              # Pin for beta stepper step signal
beta_dir_pin                                 0.11             # Pin for beta stepper direction, add '!' to reverse direction
beta_en_pin                                  0.10             # Pin for beta enable
beta_current                                 1.5              # Y stepper motor current
beta_max_rate                                30000.0          # Maxmimum rate in mm/min

gamma_step_pin                               2.2              # Pin for gamma stepper step signal
gamma_dir_pin                                0.20             # Pin for gamma stepper direction, add '!' to reverse direction
gamma_en_pin                                 0.19             # Pin for gamma enable
gamma_current                                1.5              # Z stepper motor current
gamma_max_rate                               300.0            # Maximum rate in mm/min

## Extruder module configuration
# See http://smoothieware.org/extruder
extruder.hotend.enable                          true          # Whether to activate the extruder module at all. All configuration is ignored if false
extruder.hotend.steps_per_mm                    140           # Steps per mm for extruder stepper
extruder.hotend.default_feed_rate               600           # Default rate ( mm/minute ) for moves where only the extruder moves
extruder.hotend.acceleration                    500           # Acceleration for the stepper motor mm/sec²
extruder.hotend.max_speed                       50            # Maximum speed in mm/s

extruder.hotend.step_pin                        2.8           # Pin for extruder step signal
extruder.hotend.dir_pin                         2.13          # Pin for extruder dir signal ( add '!' to reverse direction )
extruder.hotend.en_pin                          4.29          # Pin for extruder enable signal

# Extruder offset
#extruder.hotend.x_offset                        0            # X offset from origin in mm
#extruder.hotend.y_offset                        0            # Y offset from origin in mm
#extruder.hotend.z_offset                        0            # Z offset from origin in mm

# Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
#extruder.hotend.retract_length                  3            # Retract length in mm
#extruder.hotend.retract_feedrate                45           # Retract feedrate in mm/sec
#extruder.hotend.retract_recover_length          0            # Additional length for recover
#extruder.hotend.retract_recover_feedrate        8            # Recover feedrate in mm/sec (should be less than retract feedrate)
#extruder.hotend.retract_zlift_length            0            # Z-lift on retract in mm, 0 disables
#extruder.hotend.retract_zlift_feedrate          6000         # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)

delta_current                                    1.5          # First extruder stepper motor current

# Second extruder module configuration
#extruder.hotend2.enable                         true         # Whether to activate the extruder module at all. All configuration is ignored if false
#extruder.hotend2.steps_per_mm                   140          # Steps per mm for extruder stepper
#extruder.hotend2.default_feed_rate              600          # Default rate ( mm/minute ) for moves where only the extruder moves
#extruder.hotend2.acceleration                   500          # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
#extruder.hotend2.max_speed                      50           # mm/s

#extruder.hotend2.step_pin                       2.3          # Pin for extruder step signal
#extruder.hotend2.dir_pin                        0.22         # Pin for extruder dir signal ( add '!' to reverse direction )
#extruder.hotend2.en_pin                         0.21         # Pin for extruder enable signal

#extruder.hotend2.x_offset                       0            # x offset from origin in mm
#extruder.hotend2.y_offset                       25.0         # y offset from origin in mm
#extruder.hotend2.z_offset                       0            # z offset from origin in mm

#epsilon_current                                 1.5          # Second extruder stepper motor current


## Laser module configuration
# See http://smoothieware.org/laser
laser_module_enable                           false           # Whether to activate the laser module at all
laser_module_pwm_pin                          2.5             # This pin will be PWMed to control the laser.
                                                              # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
                                                              # can be used since laser requires hardware PWM, see http://smoothieware.org/pinout
#laser_module_ttl_pin                           1.30            # This pin turns on when the laser turns on, and off when the laser turns off.
#laser_module_maximum_power                   1.0             # This is the maximum duty cycle that will be applied to the laser
#laser_module_minimum_power                   0.0             # This is a value just below the minimum duty cycle that keeps the laser
                                                              # active without actually burning.
#laser_module_default_power                   0.8             # This is the default laser power that will be used for cuts if a power has not been specified.  The value is a scale between
                                                              # the maximum and minimum power levels specified above
#laser_module_pwm_period                      20              # This sets the pwm frequency as the period in microseconds

## Temperature control configuration
# See http://smoothieware.org/temperaturecontrol

# First hotend configuration
temperature_control.hotend.enable            true             # Whether to activate this ( "hotend" ) module at all.
temperature_control.hotend.thermistor_pin    0.23             # Pin for the thermistor to read
temperature_control.hotend.heater_pin        2.7              # Pin that controls the heater, set to nc if a readonly thermistor is being defined
temperature_control.hotend.thermistor        EPCOS100K        # See http://smoothieware.org/temperaturecontrol#toc5
#temperature_control.hotend.beta             4066             # Or set the beta value
temperature_control.hotend.set_m_code        104              # M-code to set the temperature for this module
temperature_control.hotend.set_and_wait_m_code 109            # M-code to set-and-wait for this module
temperature_control.hotend.designator        T                # Designator letter for this module
#temperature_control.hotend.max_temp         300              # Set maximum temperature - Will prevent heating above 300 by default
#temperature_control.hotend.min_temp         0                # Set minimum temperature - Will prevent heating below if set

# Safety control is enabled by default and can be overidden here, the values show the defaults
# See http://smoothieware.org/temperaturecontrol#runaway
#temperature_control.hotend.runaway_heating_timeout      900  # How long it can take to heat up, max is 2040 seconds.
#temperature_control.hotend.runaway_cooling_timeout        0  # How long it can take to cool down if temp is set lower, max is 2040 seconds
#temperature_control.hotend.runaway_range                20   # How far from the set temperature it can wander, max setting is 63°C

# PID configuration
# See http://smoothieware.org/temperaturecontrol#pid
#temperature_control.hotend.p_factor         13.7             # P ( proportional ) factor
#temperature_control.hotend.i_factor         0.097            # I ( integral ) factor
#temperature_control.hotend.d_factor         24               # D ( derivative ) factor

#temperature_control.hotend.max_pwm          64               # Max pwm, 64 is a good value if driving a 12v resistor with 24v.

# Second hotend configuration
#temperature_control.hotend2.enable            true           # Whether to activate this ( "hotend" ) module at all.
#temperature_control.hotend2.thermistor_pin    0.25           # Pin for the thermistor to read
#temperature_control.hotend2.heater_pin        1.23           # Pin that controls the heater
#temperature_control.hotend2.thermistor        EPCOS100K      # See http://smoothieware.org/temperaturecontrol#thermistor
##temperature_control.hotend2.beta             4066           # or set the beta value
#temperature_control.hotend2.set_m_code        104            # M-code to set the temperature for this module
#temperature_control.hotend2.set_and_wait_m_code 109          # M-code to set-and-wait for this module
#temperature_control.hotend2.designator        T1             # Designator letter for this module

#temperature_control.hotend2.p_factor          13.7           # P ( proportional ) factor
#temperature_control.hotend2.i_factor          0.097          # I ( integral ) factor
#temperature_control.hotend2.d_factor          24             # D ( derivative ) factor

#temperature_control.hotend2.max_pwm          64              # Max pwm, 64 is a good value if driving a 12v resistor with 24v.

temperature_control.bed.enable               true             # Whether to activate this ( "hotend" ) module at all.
temperature_control.bed.thermistor_pin       0.24             # Pin for the thermistor to read
temperature_control.bed.heater_pin           2.5              # Pin that controls the heater
temperature_control.bed.thermistor           Honeywell100K    # See http://smoothieware.org/temperaturecontrol#thermistor
#temperature_control.bed.beta                3974             # Or set the beta value
temperature_control.bed.set_m_code           140              # M-code to set the temperature for this module
temperature_control.bed.set_and_wait_m_code  190              # M-code to set-and-wait for this module
temperature_control.bed.designator           B                # Designator letter for this module

# Bang-bang ( simplified ) control
# See http://smoothieware.org/temperaturecontrol#bang-bang
#temperature_control.bed.bang_bang           false            # Set to true to use bang bang control rather than PID
#temperature_control.bed.hysteresis          2.0              # Set to the temperature in degrees C to use as hysteresis

## Switch modules
# See http://smoothieware.org/switch

# Switch module for fan control
switch.fan.enable                            true             # Enable this module
switch.fan.input_on_command                  M106             # Command that will turn this switch on
switch.fan.input_off_command                 M107             # Command that will turn this switch off
switch.fan.output_pin                        2.6              # Pin this module controls
switch.fan.output_type                       pwm              # PWM output settable with S parameter in the input_on_comand
#switch.fan.max_pwm                          255              # Set max pwm for the pin default is 255

#switch.misc.enable                          true             # Enable this module
#switch.misc.input_on_command                M42              # Command that will turn this switch on
#switch.misc.input_off_command               M43              # Command that will turn this switch off
#switch.misc.output_pin                      2.4              # Pin this module controls
#switch.misc.output_type                     digital          # Digital means this is just an on or off pin

#switch.bltouch.enable                    true         #
#switch.bltouch.output_pin                2.4          # sw pwm can use any digital pin
#switch.bltouch.input_on_command          M280         #
#switch.bltouch.input_off_command         M281         #
#switch.bltouch.output_type               swpwm        # sw pwm must be low frequency
#switch.bltouch.pwm_period_ms             20           # 50Hz
#switch.bltouch.startup_state             false        # start up in the stow state
#switch.bltouch.startup_value             7.43         # On boot it will go into stow mode, also set with the M281
#switch.bltouch.default_on_value          3.3          # if M280 is issued without S this is the value it will set it to


## Temperatureswitch
# See http://smoothieware.org/temperatureswitch
# Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
# Useful to turn on a fan or water pump to cool the hotend
#temperatureswitch.hotend.enable              true            #
#temperatureswitch.hotend.designator          T               # first character of the temperature control designator to use as the temperature sensor to monitor
#temperatureswitch.hotend.switch              misc            # select which switch to use, matches the name of the defined switch
#temperatureswitch.hotend.threshold_temp      60.0            # temperature to turn on (if rising) or off the switch
#temperatureswitch.hotend.heatup_poll         15              # poll heatup at 15 sec intervals
#temperatureswitch.hotend.cooldown_poll       60              # poll cooldown at 60 sec intervals

## Endstops
# See http://smoothieware.org/endstops
endstops_enable                              true             # The endstop module is enabled by default and can be disabled here
#corexy_homing                               false            # Set to true if homing on a hbot or corexy
alpha_min_endstop                            1.24^            # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
#alpha_max_endstop                           1.25^            # Pin to read max endstop, uncomment this and comment the above if using max endstops
alpha_homing_direction                       home_to_min      # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
alpha_min                                    0                # This gets loaded as the current position after homing when home_to_min is set
alpha_max                                    200              # This gets loaded as the current position after homing when home_to_max is set
beta_min_endstop                             1.26^            # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
#beta_max_endstop                            1.27^            # Pin to read max endstop, uncomment this and comment the above if using max endstops
beta_homing_direction                        home_to_min      # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
beta_min                                     0                # This gets loaded as the current position after homing when home_to_min is set
beta_max                                     200              # This gets loaded as the current position after homing when home_to_max is set
gamma_min_endstop                            1.28^            # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
#gamma_max_endstop                           1.29^            # Pin to read max endstop, uncomment this and comment the above if using max endstops
gamma_homing_direction                       home_to_min      # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
gamma_min                                    0                # This gets loaded as the current position after homing when home_to_min is set
gamma_max                                    200              # This gets loaded as the current position after homing when home_to_max is set

alpha_max_travel                             500              # Max travel in mm for alpha/X axis when homing
beta_max_travel                              500              # Max travel in mm for beta/Y axis when homing
gamma_max_travel                             500              # Max travel in mm for gamma/Z axis when homing

# Optional enable limit switches, actions will stop if any enabled limit switch is triggered
#alpha_limit_enable                          false            # Set to true to enable X min and max limit switches
#beta_limit_enable                           false            # Set to true to enable Y min and max limit switches
#gamma_limit_enable                          false            # Set to true to enable Z min and max limit switches

# Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
alpha_fast_homing_rate_mm_s                  50               # Alpha/X fast homing feedrate in mm/second
alpha_slow_homing_rate_mm_s                  25               # Alpha/X slow homing feedrate in mm/second
beta_fast_homing_rate_mm_s                   50               # Beta/Y  fast homing feedrate in mm/second
beta_slow_homing_rate_mm_s                   25               # Beta/Y  slow homing feedrate in mm/second
gamma_fast_homing_rate_mm_s                  4                # Gamma/Z fast homing feedrate in mm/second
gamma_slow_homing_rate_mm_s                  2                # Gamma/Z slow homing feedrate in mm/second

alpha_homing_retract_mm                      5                # Distance to retract from the endstop after it is hit for alpha/X
beta_homing_retract_mm                       5                # Distance to retract from the endstop after it is hit for beta/Y
gamma_homing_retract_mm                      1                # Distance to retract from the endstop after it is hit for gamma/Z


# Optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
#alpha_limit_enable                          false            # Set to true to enable X min and max limit switches
#beta_limit_enable                           false            # Set to true to enable Y min and max limit switches
#gamma_limit_enable                          false            # Set to true to enable Z min and max limit switches

# Optional order in which axis will home, default is they all home at the same time,
# If this is set it will force each axis to home one at a time in the specified order
#homing_order                                 XYZ              # X axis followed by Y then Z last
#move_to_origin_after_home                    false            # Move XY to 0,0 after homing
#endstop_debounce_count                       100              # Uncomment if you get noise on your endstops, default is 100
#endstop_debounce_ms                          1                # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
#home_z_first                                 true             # Uncomment and set to true to home the Z first, otherwise Z homes after XY

# End of endstop config
# Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
#include abc-endstop.config

## Z-probe
# See http://smoothieware.org/zprobe
zprobe.enable                                false           # Set to true to enable a zprobe
zprobe.probe_pin                             1.28!^          # Pin probe is attached to, if NC remove the !
zprobe.slow_feedrate                         5               # Mm/sec probe feed rate
#zprobe.debounce_ms                          1               # Set if noisy
zprobe.fast_feedrate                         100             # Move feedrate mm/sec
zprobe.probe_height                          5               # How much above bed to start probe
#gamma_min_endstop                           nc              # Normally 1.28. Change to nc to prevent conflict,

# Levelling strategy
# Example for 3-point levelling strategy, see wiki documentation for other strategies
#leveling-strategy.three-point-leveling.enable         true        # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
#leveling-strategy.three-point-leveling.point1         100.0,0.0   # the first probe point (x,y) optional may be defined with M557
#leveling-strategy.three-point-leveling.point2         200.0,200.0 # the second probe point (x,y)
#leveling-strategy.three-point-leveling.point3         0.0,200.0   # the third probe point (x,y)
#leveling-strategy.three-point-leveling.home_first     true        # home the XY axis before probing
#leveling-strategy.three-point-leveling.tolerance      0.03        # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
#leveling-strategy.three-point-leveling.probe_offsets  0,0,0       # the probe offsets from nozzle, must be x,y,z, default is no offset
#leveling-strategy.three-point-leveling.save_plane     false       # set to true to allow the bed plane to be saved with M500 default is false

## Panel
# See http://smoothieware.org/panel
# Please find your panel on the wiki and copy/paste the right configuration here
panel.enable                                 false             # Set to true to enable the panel code

# Example for reprap discount GLCD
# on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
# +5v is EXP1 pin 10, Gnd is EXP1 pin 9
#panel.lcd                                   reprap_discount_glcd     #
#panel.spi_channel                           0                 # SPI channel to use  ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
#panel.spi_cs_pin                            0.16              # SPI chip select     ; GLCD EXP1 Pin 4
#panel.encoder_a_pin                         3.25!^            # Encoder pin         ; GLCD EXP2 Pin 3
#panel.encoder_b_pin                         3.26!^            # Encoder pin         ; GLCD EXP2 Pin 5
#panel.click_button_pin                      1.30!^            # Click button        ; GLCD EXP1 Pin 2
#panel.buzz_pin                              1.31              # Pin for buzzer      ; GLCD EXP1 Pin 1
#panel.back_button_pin                       2.11!^            # Back button         ; GLCD EXP2 Pin 8

panel.menu_offset                            0                 # Some panels will need 1 here

panel.alpha_jog_feedrate                     6000              # X jogging feedrate in mm/min
panel.beta_jog_feedrate                      6000              # Y jogging feedrate in mm/min
panel.gamma_jog_feedrate                     200               # Z jogging feedrate in mm/min

panel.hotend_temperature                     185               # Temp to set hotend when preheat is selected
panel.bed_temperature                        60                # Temp to set bed when preheat is selected

## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
# NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
custom_menu.power_on.enable                true              #
custom_menu.power_on.name                  Power_on          #
custom_menu.power_on.command               M80               #

custom_menu.power_off.enable               true              #
custom_menu.power_off.name                 Power_off         #
custom_menu.power_off.command              M81               #


## Network settings
# See http://smoothieware.org/network
network.enable                               false            # Enable the ethernet network services
network.webserver.enable                     true             # Enable the webserver
network.telnet.enable                        true             # Enable the telnet server
network.ip_address                           auto             # Use dhcp to get ip address
# Uncomment the 3 below to manually setup ip address
#network.ip_address                           192.168.3.222   # The IP address
#network.ip_mask                              255.255.255.0   # The ip mask
#network.ip_gateway                           192.168.3.1     # The gateway address
#network.mac_override                         xx.xx.xx.xx.xx.xx  # Override the mac address, only do this if you have a conflict

## System configuration
# Serial communications configuration ( baud rate defaults to 9600 if undefined )
# For communication over the UART port, *not* the USB/Serial port
uart0.baud_rate                              115200           # Baud rate for the default hardware ( UART ) serial port

second_usb_serial_enable                     false            # This enables a second USB serial port
#leds_disable                                true             # Disable using leds after config loaded
#play_led_disable                            true             # Disable the play led

# Kill button maybe assigned to a different pin, set to the onboard pin by default
# See http://smoothieware.org/killbutton
kill_button_enable                           true             # Set to true to enable a kill button
kill_button_pin                              2.12             # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)

#msd_disable                                 false            # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
#dfu_enable                                  false            # For linux developers, set to true to enable DFU

# Only needed on a smoothieboard
# See http://smoothieware.org/currentcontrol
currentcontrol_module_enable                 true             # Control stepper motor current via the configuration file

Lien vers le commentaire
Partager sur d’autres sites

Il y a 8 heures, thab74 a dit :

quelqu'un à une idée de ou peux provenir mon erreur

oui 😉

il faut que tu enlèves les # devant les lignes qui correspondent à ton deuxième extrudeur CAD les lignes ci-dessous :

#extruder.hotend2.enable                         true         # Whether to activate the extruder module at all. All configuration is ignored if false
#extruder.hotend2.steps_per_mm                   140          # Steps per mm for extruder stepper
#extruder.hotend2.default_feed_rate              600          # Default rate ( mm/minute ) for moves where only the extruder moves
#extruder.hotend2.acceleration                   500          # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
#extruder.hotend2.max_speed                      50           # mm/s

#extruder.hotend2.step_pin                       2.3          # Pin for extruder step signal
#extruder.hotend2.dir_pin                        0.22         # Pin for extruder dir signal ( add '!' to reverse direction )
#extruder.hotend2.en_pin                         0.21         # Pin for extruder enable signal

#extruder.hotend2.x_offset                       0            # x offset from origin in mm
#extruder.hotend2.y_offset                       25.0         # y offset from origin in mm
#extruder.hotend2.z_offset                       0            # z offset from origin in mm

#epsilon_current                                 1.5          # Second extruder stepper motor current

 

 

#temperature_control.hotend2.enable            true           # Whether to activate this ( "hotend" ) module at all.
#temperature_control.hotend2.thermistor_pin    0.25           # Pin for the thermistor to read
#temperature_control.hotend2.heater_pin        1.23           # Pin that controls the heater
#temperature_control.hotend2.thermistor        EPCOS100K      # See http://smoothieware.org/temperaturecontrol#thermistor
##temperature_control.hotend2.beta             4066           # or set the beta value
#temperature_control.hotend2.set_m_code        104            # M-code to set the temperature for this module
#temperature_control.hotend2.set_and_wait_m_code 109          # M-code to set-and-wait for this module
#temperature_control.hotend2.designator        T1             # Designator letter for this module

Modifié (le) par pascal_lb
Lien vers le commentaire
Partager sur d’autres sites

Le 15/02/2020 at 23:01, pascal_lb a dit :

oui 😉

il faut que tu enlèves les # devant les lignes qui correspondent à ton deuxième extrudeur CAD les lignes ci-dessous :

#extruder.hotend2.enable                         true         # Whether to activate the extruder module at all. All configuration is ignored if false
#extruder.hotend2.steps_per_mm                   140          # Steps per mm for extruder stepper
#extruder.hotend2.default_feed_rate              600          # Default rate ( mm/minute ) for moves where only the extruder moves
#extruder.hotend2.acceleration                   500          # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
#extruder.hotend2.max_speed                      50           # mm/s

#extruder.hotend2.step_pin                       2.3          # Pin for extruder step signal
#extruder.hotend2.dir_pin                        0.22         # Pin for extruder dir signal ( add '!' to reverse direction )
#extruder.hotend2.en_pin                         0.21         # Pin for extruder enable signal

#extruder.hotend2.x_offset                       0            # x offset from origin in mm
#extruder.hotend2.y_offset                       25.0         # y offset from origin in mm
#extruder.hotend2.z_offset                       0            # z offset from origin in mm

#epsilon_current                                 1.5          # Second extruder stepper motor current

 

 

#temperature_control.hotend2.enable            true           # Whether to activate this ( "hotend" ) module at all.
#temperature_control.hotend2.thermistor_pin    0.25           # Pin for the thermistor to read
#temperature_control.hotend2.heater_pin        1.23           # Pin that controls the heater
#temperature_control.hotend2.thermistor        EPCOS100K      # See http://smoothieware.org/temperaturecontrol#thermistor
##temperature_control.hotend2.beta             4066           # or set the beta value
#temperature_control.hotend2.set_m_code        104            # M-code to set the temperature for this module
#temperature_control.hotend2.set_and_wait_m_code 109          # M-code to set-and-wait for this module
#temperature_control.hotend2.designator        T1             # Designator letter for this module

Lien vers le commentaire
Partager sur d’autres sites

Créer un compte ou se connecter pour commenter

Vous devez être membre afin de pouvoir déposer un commentaire

Créer un compte

Créez un compte sur notre communauté. C’est facile !

Créer un nouveau compte

Se connecter

Vous avez déjà un compte ? Connectez-vous ici.

Connectez-vous maintenant
×
×
  • Créer...